Question – 1
1. A ____________ is used to measure the pressure inside an engine cylinder.
-
A. screw gauge
-
B. compressor gauge
-
C. motor
-
D. plow bolt
- Answer:B
- Answer Explanation:
Question – 2
2. When _______ is poured on an engine that is overheated, it results in the cracking of the engine block.
-
A. hot water
-
B. cold water
-
C. either A or B
-
D. petrol
- Answer:A
- Answer Explanation:
Question – 3
3. ‘Pitch’ in a roof refers to __________.
-
A. slope
-
B. strength
-
C. breadth
-
D. height
- Answer:A
- Answer Explanation:
Question – 4
4. ________ are used for setting nails below the surface of wood.
-
A. Ripsaws
-
B. Nail sets
-
C. Bucking bars
-
D. Piston rings
- Answer:B
- Answer Explanation:
Question – 5
5. _________ consist of a handle, head, face, claw (for pulling nails) and a wedge.
-
A. Axles
-
B. Pliers
-
C. Hammers
-
D. Coils
- Answer:C
- Answer Explanation:
Question – 6
6. A _________ protects the breaker point from damage by absorbing excess current during high-voltage surge.
-
A. chisel
-
B. nut
-
C. compressor
-
D. condenser
- Answer:D
- Answer Explanation:
Question – 7
7. In an engine cooling system, _______ surround the engine parts that reach the highest temperatures.
-
A. Water Jackets
-
B. Plugs
-
C. Radiators
-
D. Nails
- Answer:A
- Answer Explanation:
Question – 8
8. An alternator in a car charges the electronic gadgets _________.
-
A. only if the car is moving
-
B. only when the car is at rest
-
C. both A and B
-
D. only during cool climates
- Answer:C
- Answer Explanation:
Question – 9
9. ‘R’ in tire ratings stands for _______.
-
A. Radial
-
B. Radiation
-
C. Rotation
-
D. None of the above
- Answer:A
- Answer Explanation:
Question – 10
10. In a rear-wheel drive, the rear wheels ________.
-
A. pull the car
-
B. push the car
-
C. push and pull the car
-
D. make the car move in forward direction only
- Answer:B
- Answer Explanation:
Question – 11
11. The taps are used for _________.
-
A. detecting vibration
-
B. drilling
-
C. cutting internal threads
-
D. cutting external threads
- Answer:C
- Answer Explanation:
Question – 12
12. What is the common factor between starting system components such as the starter, motor, solenoid and/or relay?
-
A. They operate on A/C current.
-
B. They are parallel to each other.
-
C. They use the principles of electromagnetism.
-
D. They are controlled mechanically.
- Answer:C
- Answer Explanation:
Question – 13
13. Insert the _________ into the ________ to use a bit in a hand drill.
-
A. spur ; chuck
-
B. auger ; base
-
C. lip ; flute
-
D. tang ; chuck
- Answer:D
- Answer Explanation:
Question – 14
14. Which of the following is measured using a contour gauge?
-
A. The diameter of an object.
-
B. The size of an object.
-
C. The width of an object.
-
D. The length of an object.
- Answer:B
- Answer Explanation:
Question – 15
15. What will be the effect of adding additional resistance to an automotive electrical series circuit?
-
A. It will reduce the current flow
-
B. It will not affect the current flow
-
C. It will increase the voltage
-
D. It will increase the current flow
- Answer:A
- Answer Explanation: