Question – 1
1. A ____________ is used to measure the pressure inside an engine cylinder.
- A. screw gauge
- B. compressor gauge
- C. motor
- D. plow bolt
- Answer:B
- Answer Explanation:
Question – 2
2. When _______ is poured on an engine that is overheated, it results in the cracking of the engine block.
- A. hot water
- B. cold water
- C. either A or B
- D. petrol
- Answer:A
- Answer Explanation:
Question – 3
3. ‘Pitch’ in a roof refers to __________.
- A. slope
- B. strength
- C. breadth
- D. height
- Answer:A
- Answer Explanation:
Question – 4
4. ________ are used for setting nails below the surface of wood.
- A. Ripsaws
- B. Nail sets
- C. Bucking bars
- D. Piston rings
- Answer:B
- Answer Explanation:
Question – 5
5. _________ consist of a handle, head, face, claw (for pulling nails) and a wedge.
- A. Axles
- B. Pliers
- C. Hammers
- D. Coils
- Answer:C
- Answer Explanation:
Question – 6
6. A _________ protects the breaker point from damage by absorbing excess current during high-voltage surge.
- A. chisel
- B. nut
- C. compressor
- D. condenser
- Answer:D
- Answer Explanation:
Question – 7
7. In an engine cooling system, _______ surround the engine parts that reach the highest temperatures.
- A. Water Jackets
- B. Plugs
- C. Radiators
- D. Nails
- Answer:A
- Answer Explanation:
Question – 8
8. An alternator in a car charges the electronic gadgets _________.
- A. only if the car is moving
- B. only when the car is at rest
- C. both A and B
- D. only during cool climates
- Answer:C
- Answer Explanation:
Question – 9
9. ‘R’ in tire ratings stands for _______.
- A. Radial
- B. Radiation
- C. Rotation
- D. None of the above
- Answer:A
- Answer Explanation:
Question – 10
10. In a rear-wheel drive, the rear wheels ________.
- A. pull the car
- B. push the car
- C. push and pull the car
- D. make the car move in forward direction only
- Answer:B
- Answer Explanation:
Question – 11
11. The taps are used for _________.
- A. detecting vibration
- B. drilling
- C. cutting internal threads
- D. cutting external threads
- Answer:C
- Answer Explanation:
Question – 12
12. What is the common factor between starting system components such as the starter, motor, solenoid and/or relay?
- A. They operate on A/C current.
- B. They are parallel to each other.
- C. They use the principles of electromagnetism.
- D. They are controlled mechanically.
- Answer:C
- Answer Explanation:
Question – 13
13. Insert the _________ into the ________ to use a bit in a hand drill.
- A. spur ; chuck
- B. auger ; base
- C. lip ; flute
- D. tang ; chuck
- Answer:D
- Answer Explanation:
Question – 14
14. Which of the following is measured using a contour gauge?
- A. The diameter of an object.
- B. The size of an object.
- C. The width of an object.
- D. The length of an object.
- Answer:B
- Answer Explanation:
Question – 15
15. What will be the effect of adding additional resistance to an automotive electrical series circuit?
- A. It will reduce the current flow
- B. It will not affect the current flow
- C. It will increase the voltage
- D. It will increase the current flow
- Answer:A
- Answer Explanation: