Question – 1
1. When fuel is mixed with air by the fuel system, the particles of the fuel are___________.
-
A. randomized
-
B. atomized
-
C. minimized
-
D. compressed
- Answer:B
- Answer Explanation:
Question – 2
2. A typical rich air-fuel mixture is __________.
-
A. 1: 10
-
B. 7: 10
-
C. 10: 1
-
D. 10: 7
- Answer:C
- Answer Explanation:
Question – 3
3. ___________ takes place when an engine’s air-fuel mixture is lean.
-
A. Detonation
-
B. Depression
-
C. Impression
-
D. Preignition
- Answer:A
- Answer Explanation:
Question – 4
4. A __________ is utilized by the diesel engine.
-
A. spark ignition system
-
B. low compression ratio
-
C. high compression ratio
-
D. carburetor
- Answer:C
- Answer Explanation:
Question – 5
5. What is the role of antifreeze in an engine coolant?
-
A. It lowers the boiling point of the coolant
-
B. It raises the boiling point of the coolant
-
C. It raises the freezing point of the coolant
-
D. It lowers the corrosion resistance of the coolant
- Answer:B
- Answer Explanation:
Question – 6
6. Which of the following controls the electronic fuel injectors?
-
A. Fuel pressure regulator
-
B. Electric fuel pump
-
C. Ignition switch
-
D. Powertrain control module
- Answer:D
- Answer Explanation:
Question – 7
7. What are the two basic types of wrenches?
-
A. The open end and the box end
-
B. The open end and the close end
-
C. The start end and close end
-
D. None of the above
- Answer:A
- Answer Explanation:
Question – 8
8. A veining bit is used in a _________ to cut fine lines in materials, often for decorative purposes.
-
A. hand drill
-
B. electric saw
-
C. drill press
-
D. router
- Answer:D
- Answer Explanation:
Question – 9
9. _________ to stop a board from chipping on the end as you plane.
-
A. At the end of the board insert a nail to hold it together
-
B. A piece of wood can be nailed to the end of the board as an extension of the board
-
C. After planing, cut off the end
-
D. After finishing, glue the chipped pieces back
- Answer:B
- Answer Explanation:
Question – 10
10. _________ is a process that joins metals by bonding a metal alloy to their surfaces.
-
A. Planing
-
B. Smoothing
-
C. Soldering
-
D. Shaping
- Answer:C
- Answer Explanation:
Question – 11
11. __________ are used when it is necessary to disassemble a component by hand.
-
A. Electric saws
-
B. Cotter pins
-
C. Lock nuts
-
D. Wing nuts
- Answer:D
- Answer Explanation:
Question – 12
12. UNF stands for which one of the thread classifications?
-
A. Unified National Fine
-
B. Unified National Fund
-
C. United National Fund
-
D. United Name Fine
- Answer:A
- Answer Explanation:
Question – 13
13. ___________ is used to loosen a bolt with a hexagonal head.
-
A. A box-end wrench
-
B. A12-point socket and ratchet
-
C. An open-end wrench
-
D. All of the above
- Answer:D
- Answer Explanation:
Question – 14
14. The threaded fasteners that are 1/4 inch or more in diameter are known as ________.
-
A. Nuts
-
B. Machine screws
-
C. Bolts
-
D. Rivets
- Answer:C
- Answer Explanation:
Question – 15
15. ___________ are electronically connected to EFI computer.
-
A. Carburetors
-
B. Injectors
-
C. Throttles
-
D. Radiators
- Answer:C
- Answer Explanation: